Hey fellow Selfhosters! I need some help, I think, and searching isn’t yielding what I’m hoping for.
I recently built a new NAS for my network with 4x 18TB drives in a ZFS raidz1 pool. I previously have been using an external USB 12TB harddrive attached to a different machine.
I’ve been attempting to use rsync to get the 12TB drive copied over to the new pool and things go great for the first 30-45 minutes. At that point, the current copy speed diminishes and 4 current files in progress sit at 100% done. Eventually, I’ve had to reboot the machine, because the zpool doesn’t appear accessible any longer. After reboot, the pool appears fine, no faults, and I can resume rsync for a while.
EDIT: Of note, the rsync process seems to stall and I can’t get it to respect SIGINT or Ctrl+C. I can SSH in separately and running zpool status hangs with no output.
While the workaround seems to be partially successful, the point of using rsync is to make it fairly hands-free and it’s been a week long process to copy the 3TB that I have now. I don’t think my zpool should be disappearing like that! Makes me nervous about the long-term viability. I don’t think I’m ready to drop down on Unraid.
rsync is being initiated from the NAS to copy from the old server, am I better off “pushing” than “pulling”? I can’t imagine it’d make much difference.
Could my drives be bad? How could I tell? They’re attached to a 10 port SATA card, could that be defective? How would I tell?
Thanks for any help! I’ve dabbled in linux for a long time, but I’m far from proficient, so I don’t really know the intricacies of dmesg et al.
Just to make sure. Are you copying to your ZFS pool directory or a dataset? Check to male sure your paths are correct.
Push vs pull shouldn’t matter but I’ve always done push.
If your zpool is not accessible anymore after a transfer then there is a low-level problem here as it shouldn’t just disappear.
I would installe tmux on your ZFS system and have a window with htop running, dmesg, and zpool status running to check your system while you copy files. Something that severe should become self evedent pretty quickly.
The drives in the zpool, are they SMR drives? Slow write speed and disks dropping out are a symptom of I remember correctly
I don’t think they make SMR drives that big
They’re Seagate Exos, https://www.seagate.com/products/cmr-smr-list/ and appear to be CMR
So next I’d be checking logs for sata errors, pcie errors and zfs kernel module errors. Anything that could shed light on what’s happening. If the system is locking up could it be some other part of the server with a hardware error, bad ram, out of memory, bad or full boot disk, etc.
Have you tried running it overnight to make sure its not just a performance thing?
I did, great suggestion. It never recovered.
deleted by creator
One thing I haven’t seen mentioned here, zfs can be quite finicky with some sata cards, especially raid cards.
I suggest you connect the hard drives to the motherboard directly and test again.
Thank you! I ended up connecting them directly to the main board and had the same result with rsync, eventually the zpool becomes inaccessible until reboot (ofc there may be other ways to recover it without reboot).
I don’t have practical experience with ZFS, but my understanding is that it uses RAM a lot… if that’s new, it might be worth checking the RAM by booting up memtest (for example) and just ruling that out.
Maybe also worth watching the system with
nmonorhtop(running in anothertmux/screenpane) at the beginning of the next session, then when you think it’s jammed up, see what looks different…Awesome, thanks for giving some clues. It’s a new build, but I didn’t focus hugely on RAM, I think it’s only 32GB. I’ll try this out.
Edit: I did some reading about L2ARC, so pending some of these tests, I’m planning to get up to 64gb ram and then extend with an l2arc SSD, assuming no other hardware errors.
Based on this thread it’s the deduplication that requires a lot of RAM.
See also: https://wiki.freebsd.org/ZFSTuningGuide
Edit: from my understand the pool shouldn’t become inaccessible tho and only get slow. So there might be another issue.
Edit2: here’s a guide to check whether your system is limited by zfs’ memory consumption: https://github.com/openzfs/zfs/issues/10251
I believe there’s another issue. ZFS has been using nearly all RAM (which is fine, I only need RAM for system and ZFS anyway, there’s nothing else running on this box), but I was pretty convinced while I was looking that I don’t have dedup turned on. Thanks for your suggestions and links!
Just another thought… Maybe just format the drives as a massive EXT4 JBOD (just for a temp test) and copy the data again - just to see if ZFS is the problem… maybe it’s something else altogether? Maybe - and I hope not - the USB source drive is failing after long reads?
When things lock up, will a kill -9 kill rsync or not? If it doesn’t, and the zpool status lockup is suspicious, it means things are stuck inside a system call. I’ve seen all sorts of horrible things with usb timeouts. Check your syslog.
kill -9
Just tested, thanks for the suggestion! It killed a few instances of
rsync, but there are two apparently stuck open. I issuedrebootand the system seemed to hang while waiting forrsyncto be killed and failed to unmount the zpool.Syslog errors:
Dec 31 16:53:34 halnas kernel: [54537.789982] #PF: error_code(0x0002) - not-present page Jan 1 12:57:19 halnas systemd[1]: Condition check resulted in Process error reports when automatic reporting is enabled (file watch) being skipped. Jan 1 12:57:19 halnas systemd[1]: Condition check resulted in Process error reports when automatic reporting is enabled (timer based) being skipped. Jan 1 12:57:19 halnas kernel: [ 1.119609] pcieport 0000:00:1b.0: DPC: error containment capabilities: Int Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+ Jan 1 12:57:19 halnas kernel: [ 1.120020] pcieport 0000:00:1d.2: DPC: error containment capabilities: Int Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+ Jan 1 12:57:19 halnas kernel: [ 1.120315] pcieport 0000:00:1d.3: DPC: error containment capabilities: Int Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+ Jan 1 22:59:08 halnas kernel: [ 1.119415] pcieport 0000:00:1b.0: DPC: error containment capabilities: Int Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+ Jan 1 22:59:08 halnas kernel: [ 1.119814] pcieport 0000:00:1d.2: DPC: error containment capabilities: Int Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+ Jan 1 22:59:08 halnas kernel: [ 1.120112] pcieport 0000:00:1d.3: DPC: error containment capabilities: Int Msg #0, RPExt+ PoisonedTLP+ SwTrigger+ RP PIO Log 4, DL_ActiveErr+ Jan 1 22:59:08 halnas systemd[1]: Condition check resulted in Process error reports when automatic reporting is enabled (file watch) being skipped. Jan 1 22:59:08 halnas systemd[1]: Condition check resulted in Process error reports when automatic reporting is enabled (timer based) being skipped. Jan 2 02:23:18 halnas kernel: [12293.792282] gdbus[2809399]: segfault at 7ff71a8272e8 ip 00007ff7186f8045 sp 00007fffd5088de0 error 4 in libgio-2.0.so.0.7200.4[7ff718688000+111000] Jan 2 02:23:22 halnas kernel: [12297.315463] unattended-upgr[2810494]: segfault at 7f4c1e8552e8 ip 00007f4c1c726045 sp 00007ffd1b866230 error 4 in libgio-2.0.so.0.7200.4[7f4c1c6b6000+111000] Jan 2 03:46:29 halnas kernel: [17284.221594] #PF: error_code(0x0002) - not-present page Jan 2 06:09:50 halnas kernel: [25885.115060] unattended-upgr[4109474]: segfault at 7faa356252e8 ip 00007faa334f6045 sp 00007ffefed011a0 error 4 in libgio-2.0.so.0.7200.4[7faa33486000+111000] Jan 2 07:07:53 halnas kernel: [29368.241593] unattended-upgr[4109637]: segfault at 7f73f756c2e8 ip 00007f73f543d045 sp 00007ffc61f04ea0 error 4 in libgio-2.0.so.0.7200.4[7f73f53cd000+111000] Jan 2 09:12:52 halnas kernel: [36867.632220] pool-fwupdmgr[4109819]: segfault at 7fcf244832e8 ip 00007fcf22354045 sp 00007fcf1dc00770 error 4 in libgio-2.0.so.0.7200.4[7fcf222e4000+111000] Jan 2 12:37:50 halnas kernel: [49165.218100] #PF: error_code(0x0002) - not-present page Jan 2 19:57:53 halnas kernel: [75568.443218] unattended-upgr[4110958]: segfault at 7fc4cab112e8 ip 00007fc4c89e2045 sp 00007fffb4ae2d90 error 4 in libgio-2.0.so.0.7200.4[7fc4c8972000+111000] Jan 3 00:54:51 halnas snapd[1367]: stateengine.go:149: state ensure error: Post "https://api.snapcraft.io/v2/snaps/refresh": net/http: request canceled while waiting for connection (Client.Timeout exceeded while awaiting headers)
